1. Calculate the overall heat-transfer coefficient (U=?) for a frame construction wall made of brick veneer (120-lbm/ft³) with 3-in. fiberglass insulation bats between the 2x4 wood studs (softwood) that are 16-in. on center. The wind velocity is 15-mph. Fill out the table below also utilizing materials data from the textbook. Also, calculate the total heat loss if the referenced wall was 9-ft tall and 35-ft in length set in Ohio, Clevland @ 99% winter OAT with an indoor setpoint of 75°F. Hint: 2x4 wood studs are 16-in. on center and 2-in. thick by 4-in. deep thus the empty space between each stud is 14-in. Remember use R = L/K & R = 1/C for materials. Between Frame (R-Value) At Framing (R-Value) Outside Surface 4-in. Face Brick (k=middle value) 12-in. Sheathing reg. density 3-in. Insulation Batt 2"x4" Wood Studs (k=middle value) 1/2-in. Gypsum Board Inside Surface Total (R-Value): U= Btu/(hr-ft²°F)

1. Calculate the overall heat-transfer coefficient (U=?) for a frame construction wall made of brick veneer (120-lbm/ft³) with 3-in. fiberglass insulation bats between the 2x4 wood studs (softwood) that are 16-in. on center. The wind velocity is 15-mph. Fill out the table below also utilizing materials data from the textbook. Also, calculate the total heat loss if the referenced wall was 9-ft tall and 35-ft in length set in Ohio, Clevland @ 99% winter OAT with an indoor setpoint of 75°F. Hint: 2x4 wood studs are 16-in. on center and 2-in. thick by 4-in. deep thus the empty space between each stud is 14-in. Remember use R = L/K & R = 1/C for materials. Between Frame (R-Value) At Framing (R-Value) Outside Surface 4-in. Face Brick (k=middle value) 12-in. Sheathing reg. density 3-in. Insulation Batt 2"x4" Wood Studs (k=middle value) 1/2-in. Gypsum Board Inside Surface Total (R-Value): U= Btu/(hr-ft²°F)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An oil storage tank has 20mm steel walls covered with 50mm of fiber glass insulation. if the oil temperature is kept at 150 degree Celsius, what is the rate of heat loss when the outside temperature is 20 degree Celsius and external air coefficient is 20W/m². How much would the heat loss be reduced by doubling the thickness of the insulation?
c) A steel pipe of 100 mm bore, and 10 mm bore thickness, carrying dry saturated steam at 28 bars, is insulated with a 40 mm layer of moulded insulation. This insulation in turn is insulated with a 60 mm layer of felt. The atmospheric temperature is 15 °C. Calculate: (i) the rate of heat loss by the steam per metre pipe length. (ii) the temperature of the outside Dimensions in mm surface.zzzzzzz h₂-15 W/m²K Steel k₁=50 W/mK AVALEHT Ø100 1₂ " Steam 28 bar h-550 W/m²K, Inner heat transfer coefficient = 550 W/m² K Outer heat transfer coefficient = 15 W/m² K Thermal conductivity of steel = 50 W/m K Thermal conductivity of felt = 0.07 W/m K Moulded insulation Felt Moulded insulation K₂=0.09 W/mK Thermal conductivity of moulded insulation = 0.09 W/m 40 10. A 60 15°C Felt K₁=0.07 W/mK zzzzzzzz
Q2/ A composite wall is formed of a 2.5 cm copper plate, a 3.2 mm layer of asbestos, and a 5 cm layer of fiberglass. The wall is subjected to an overall temperature difference of 560 C. Calculate the heat flow per unit area through the composite structure.
Qigihar House in Heilongiiang Province, China Heat Loss Problems, BSCl 2101 Climate: Avg. remperature is 3.2°C Degree Days is 5000 Inside Air Temp. is 20°C Wall Construction, Inside to Out: 15mm Gypsum Plaster, Sand Aggregate Concrete Block, rectangular core, Sand and Gravi 15mm Cement Plaster, Sand Aggregate All 4 walls measure the same, 8m wide by 7mtall. The house is heated with electricity at a cost of $0.10kWh Calculate the RSI-total for the walls using the tabular method demonstrated in class, and the temperature drop through each element for the January 2.5% temperature. Calculate the rate of heat flow through the wall again for the January 2.5% temperature. Plot the temperature profile approximately to scale through a vertical cross-section of the wall. Calculate the January heating cost for the building. Calculate the annual heating cost for the building. Now add 2" ( 50.8mm ) of extruded polystyrene, smooth skin surface, 35kgm3 rigid insulation to the inside surfaces…
Q7/ A hollow sphere is constructed of aluminum with an inner diameter of 4 cm and an outer diameter of (8cm). The inside temperature is (100-C) and the outer temperature is (50•C). Calculate the heat transfer.
An office space contains one (6`x 3`) well- fitted door made of nominal 2" wood. The heat loss through door by infiltration is (3381 Btuh) if Tb.l.=80 F , To= -10 F , and Vwind=15 mph ? True or false
Do a quick calculation of the thermal conductance (U value) across a cavity wall consisting of: Outer skin 220mm brickwork (North facing, exposed aspect) 20mm cavity Inner skin of 10mm plasterboard
Please solve asap, Will provide helpful ratings for complete solution. Thank u A double-glazed window is constructed such that it has 5 mm thick glass as the inside layer, 4 mm layer of gas, and finally 5 mm thick glass as the outer layer. Which have thermal conductivies of 0.7, 2.120, and 5.9 W m-1 K-1, respectively. Calculate the heat loss per unit area, Wm-2 through the glass if the inside temperature of the glass is 11.09 °C and the outside temperature is 6.47 °C Report your answer to 2 decimal places.
A domestic pitched roof of tiles on felt sacking with a plasterboard ceiling has an existing u-value of 1.9w/m2k. Calculate the minimum thickness of fibre glass insulation in the roof space required to give the roof a new u-value of 0.25w/m2k. The thermal conductivity of the fibre glass used is 0.04w/mk
For a flat corrugated galvanized steel (conductivity = 26 W/m.K) roof 1/32 in. thick lined with a ¼ in. asbestos-cement (conductivity = 1.2 W/m.K) ceiling 6 inches below the roof, with downward heat flow, calculate the overall thermal transmittance of the roof.
Presents the diagram of the problem, necessary formulas, clearance and numerical solution: A metal plate 4 mm thick has a temperature difference between its two faces of 32 ◦C. It transmits 200 kcal/h through an area of 5 cm2. Calculate the thermal conductivity of the metal in W/m K.
A wall is made up of brick of thermal conductivity 1.0 W/(m.K),230 mm thick .It is lined on the inner face with plaster of thermal conductivity of 0.4 W/(m.K),and of thickness 10 mm .If a temperature difference of 30K is maintained between the two faces .What is the heat flow per unit area of wall?