please answer all with complete solution, thank you. 1. Calculate the minimum wall thickness for a cylindrical vessel. The diameter of the vesselis 8.5 meters and the stress is limited to 47 MPa. It is filled with motor oil.w- unit weight of motor oil = 8.95 KN/msure vEe ulameter.h = 12.3mD=7 m2. A cylindrical pressure vessel is fabricated from steel plates which have a thickness of 20mm. The diameter of the pressure vessel is 601 mm and its length is 4 meters. Determinethe maximum internal pressure which can be applied if the stress in the steel is limited to140 MPa.

Answered: Image /qna-images/answer/32275989-ba83-4b58-8ddf-8d6a3a7dab2b.jpg

1. Calculate the minimum wall thickness for a cylindrical vessel. The diameter of the vessel is 8.5 meters and the stress is limited to 47 MPa. It is filled with motor oil. w- unit weight of motor oil = 8.95 KN/m sure vEel ulameter. h = 12.3m D = 7 m 2. A cylindrical pressure vessel is fabricated from steel plates which have a thickness of 20 mm. The diameter of the pressure vessel is 601 mm and its length is 4 meters. Determine the maximum internal pressure which can be applied if the stress in the steel is limited to 140 MPa.

1. Calculate the minimum wall thickness for a cylindrical vessel. The diameter of the vessel is 8.5 meters and the stress is limited to 47 MPa. It is filled with motor oil. w- unit weight of motor oil = 8.95 KN/m sure vEel ulameter. h = 12.3m D = 7 m 2. A cylindrical pressure vessel is fabricated from steel plates which have a thickness of 20 mm. The diameter of the pressure vessel is 601 mm and its length is 4 meters. Determine the maximum internal pressure which can be applied if the stress in the steel is limited to 140 MPa.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

FIG. P8.8
8-1 A spherical gas tank has an inner radius of r = 1.5 m. If it is subjected to an internal pressure of p = 300 kPa, determine its required thickness if the maximum normal stress is not to exceed 12 MPa.
Assuming that pressure will increase at a uniform rate and there is no damping of the pressure wave. Water from a reservoir that flows through a 650mm pipe at 1.8m/s is completely stopped by a closure of a 160 m valve from the reservoir. The thickness of the pipe is 25mm, bulk modulus of water is 2.2x10⁹ Pa and E of steel is 1.4x10¹¹ Pa. Determine the following: a. Celerity of the pressure wave b. Equivalent bulk modulus of water c. Pressure on the pipe after closure of the valve d. Time required to avoid water hammer e. Water hammer pressure of the velocity will decrease to 1.2m/s f. Maximum permissible discharge after the outlet valve closure. ANSWER: d) t = 0.256 sec. e) Ph=pCAV = 749.8476 kPa f) Q = AV = 0.597 m³/s a) C = 1249.746m/s b) k' = 1.562x10⁹ Pa c) Ph=pCV = 2249.5428 kPa
The tank shown is fabricated from steel plate. Determine the minimum thickness of the plate which may be used if the stress is limited to 40 MN/m² and the internal pressure is 1.5 MN/m².
A welded steel cylindrical drum made of a 10-mm plate has an internal diameter of 1.20 m & height of 4m. Compute the change in length that would be caused by an internal pressure of 1.5 MPa. Assume that Poisson's ratio is 0.30 andE = 200 GPa. * thickness, t= 10 mm 1.20 m O 0.270 mm O 0.360 mm O 0.108 mm O 0.459 mm.
8.1 A spherical shell with 70-in. outer diameter and 67-in. inner diameter contains helium at a pressure of 1200 psi. Compute the stress in the shell. 8.2 A spherical pressure vessel has a 1.5-ft inner radius and 3/16-in. wall thickness. If the working tensile stress of the material is 6000 psi, determine the maximum
1. A cylindrical pressure vessel is fabricated from steel plates which have a thickness of 20 mm. The diameter of the pressure vessel is 600mm. and its length is 4 meters. Determine the maximum internal pressure which can be applied if the stress in the steel is limited to 140 MPa. 2. Calculate the minimum wall thickness for a cylindrical vessel shown. The diameter of a vessel is 8.5 meters, the height is 12.3 meters and the stress in limited to 47 MPa. It is filled with motor oil. w - unit weight of motor oil= 8.95 KN/m Please help me to answer these questions thank you so much
Castor oil is subjected to a pressure of 470 kPa at A and to a pressure of 200 kPa at B. The pipe has a diameter of 30 mm. Take Pco = 960 kg/m³ and Heo = 0.985 N -s/m? (Figure 1) B' 12 m Determine the shear stress acting on the pipe wall. Express your answer to three significant figures and include the appropriate units. Determine the maximum velocity of the oil. Express your answer to three significant figures and include the appropriate units. What is the flow Q? Express your answer using three significant figures.
The tank shown in Figure (1) is made from plates have 5 mm thickness and allowable stress of D 90 MPa. Determine the required value of depth (D) as a semicircle diameter if the internal pressure is 1 MPa. 700 mm Figure (1)
A cylindrical tank holding oxygen at 1,146 kPa pressure has an outside diameter of 430 mm and a wall thickness of 13 mm. Compute the hoop stress (in MPa) in the wall of the cylinder.
Question-8, A cylindrical pressure vessel is1200 mm in diameter. It is made of rolled mild steel plate. The vessel is subjected to an internal pressure of 2 N/mmt. If the material yields at 200 N/mmt, what should be the minimum safe thickness of the plate, based on Maximum Principal Stress Theory?(FOS-1.5)
8.9 A cylindrical steel pressure vessel has a 400-mm inner radius and 8-mm-thick walls. Find the change in the inner radius when the vessel is pressurized to 1.2 MPa. Use E = 200 GPa and v = 0.3 for steel.