1. A. Using the Steam Tables, determine the amount of cooling water needed by a condenser in kg/sec if wet steam comes into the condenser at P= 610.44mmHG vac and 99.47 % moisture, mass flow rate= 7200+ (X/SN) kg/hr. Cooling water enters the condenser at 12 deg C and leaves at 21 deg C. Answer: 8. Draw the schematic diagram of the condenser and process in the PV and TS diagrams below. Cp H20-4.187 KI/kg-K):

1. A. Using the Steam Tables, determine the amount of cooling water needed by a condenser in kg/sec if wet steam comes into the condenser at P= 610.44mmHG vac and 99.47 % moisture, mass flow rate= 7200+ (X/SN) kg/hr. Cooling water enters the condenser at 12 deg C and leaves at 21 deg C. Answer: 8. Draw the schematic diagram of the condenser and process in the PV and TS diagrams below. Cp H20-4.187 KI/kg-K):

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter40: Typical Operating Conditions

Section: Chapter Questions

Problem 2RQ: The typical temperature relationship between a standard-efficiency air-cooled condenser and the...

See similar textbooks

Similar questions

Define a near-azeotropic refrigerant blend, and give twoexamples.
A. Using the steam tables, determine the amount of coolimg water needed by a condenser in kg/sec if wet steam comes into the condenser at P= 610.44mmHG vac and 99.47% moisture, mass flow rate= 7200 + (100 (value of x) /25 (value of SN)) kg/hr. Cooling water enters the condenser at 12 deg C and leaves at 21 deg C. Answer: ___ B. Draw the schematic diagram if the condeser and process in the PV and TS diagram. Cp H2O= 4.187 KJ/(kg-K) The value 100/25 signify X/SN
A. Using the steam tables, determine the amount of coolimg water needed by a condenser in kg/sec if wet steam comes into the condenser at P= 610.44mmHG vac and 99.47% moisture, mass flow rate= 7200 + (100/25) kg/hr. Cooling water enters the condenser at 12 deg C and leaves at 21 deg C. Answer: ___ B. Draw the schematic diagram if the condeser and process in the PV and TS diagram. Cp H2O= 4.187 KJ/(kg-K)
1. A. Using the Steam Tables, determine the amount of cooling water needed by a condenser in kg/sec if wet steam comes into the condenser at P= 610.44mmHG vac and 99.47 % moisture , mass flow rate = 7200 + (SN/X) kg/hr. Cooling water enters the condenser at 12 deg C and leaves at 21 deg C. Answer: B. Draw the schematic diagram of the condenser and process in the PV ahd TS diagrams below. Cp H2O = 4.187 KJ/(kg-K): Schematic diagram of heat exchanger =condenser
1. A. Using the Steam Tables, determine the amount of cooling water needed by a condenser in kg/sec if wet steam comes into the condenser at P= 610.44mmHG vac and 99.47 % moisture, mass flow rate= 7200+ (X/SN) kg/hr. Cooling water enters the condenser at 12 deg C and leaves at 21 deg C. Answer: B. Draw the schematic diagram of the condenser and process in the PV and TS diagrams below. Cp H20 = 4.187 KJ/(kg-K): Schematic diagram of heat exchanger =condenser S 2. Use only the MD below to solve this Item; use it by plotting data and process to determine items being asked. Steam enters a turbine at 117.4308 atmgage and 932 deg. F, and expands isentropicaly to 177.17 inches of Hg. For 2 + (X/SN) kg/sec of steam, what is (a) the ideal work done (KI/sec) if AKE = 0 and actual exhaust enthalpy is 2700 KI/kg. a)Ans: (b)ne =_ (c)Determine: (e) Actual steam temp ideal steam moisture at exhaust. Ans: at the exhaust. Ans. g) change in entropy during the actual process. Ans 3000 2500 2000…
Draw the schematic and p-h diagram for the problem below: A two-stage cascade refrigeration system uses ammonia as the working substance. The evaporator is at -35 degree Celsius and high pressure condenser is at 1514.2 kPa. The cascade condenser is a direct-contact type. The refrigeration load is 90 tons. Determine the a.) the COP, and b.) the quantity of the fluid entering.
I. Condensing temperature = 40 C II. Evaporating temperature = 5 C III. Temperature of solution entering generator = 80 C IV. Temperature of solution leaving generator = 100 C V. Assume saturated conditions for states 3, 4, 8, and 10. VI. Saturated steam at 0.2 MPa enters the generator and leaves as saturate water: Compute: a. the required mass flow rate of the steam (kg/hr) per kW of refrigeration produced b. the Heat Rejection Ratio, HRR = (Qabsorber + Qcondenser)/Qevaporator of the system.
1 atm steam (sat.) preheats CO2. If 2.26 MJ heat is released from 1kg of condensing steam, How much saturated steam is needed to condense to that 21 kg/s CO2is preheated from 303.15 K to 353.15 K? Cp CO2 = 4.5R, where R = 8.314 J/mol K. a. 0.40 kg/s b. 0.36 kg/s c. 0.30 kg/s d. 0.18 kg/s
PLEASE DO NOT USE PSYCHROMETRIC CHART. THANK YOU In the diagram below inlet air is drawn over a pool of liquid water in a steady-state, steady-flow isobaric process. Evaporation on the pool resultsin saturated air at the exit. The pool of liquid water is assumed to be at the same temperature as the exitair. Discharge fans at the exit provide a volumetric flow rate of 800,000 ft3/min. Problem #2: Assume that the R134a chiller is turned off such that Qout = 0, but the evaporative coolersystem continues to operate. Determine:a) The exit temperature, T2 (°F)b) The mass flow rate dry air through the system (lbm/sec).c) The rate of liquid water resupply required for continuous operation (lbm/hour).
The LiBr-water absorption cycle shown in Fig. 17-2 operates at the following temperatures: generator, 100°C; condenser, 55°C; evaporator, 10°C, and absorber, 30°C. The flow rate of solution delivered by the pump is 0.4 kg/s. What is the concentration of Li-Br in the generator?
Q.1. A refrigeration process with interstage cooling uses refrigerant HFC-134a, and the outlet of the condenser is to be saturated liquid at 40°C. Refer to the following figure for stream numbers in your solution. The pressure of the flash chamber and the intermediate pressure between compressors is to be 290 kPa. The evaporator is to operate at -20°C and the outlet is to be saturated vapor. The flowrate of stream 1 is 23 kg/h. The flash chamber may be considered adiabatic. The compressors may be considered to be 80% efficient. a) What is the power input required to the first compressor? b) What are the flowrates of streams 6 and 7? What is the enthalpy of stream 4? Hot Side 6 5 Condenser 2nd Stage Compressor Throttle Valve 7 Flash Chamber Vapor Phase Only 1st Stage Compressor 8 Throttle Valve Evaporator 1 2 Cold Side
Given the following information about a condenser system, determine the fan power requirement, Fp:1. Emission stream flow rate (Qe,a) = 2050 acfm2. Condenser system pressure drop (P) = 5 in. H2O3. Condenser system operating hours per year (HRS) = 6000 h/yr