1) Three loads are connected in parallel across a 1400 V, 60 Hz, single phase as shown in below: 1400 V I Load Load 1: Inductive Load 2: Capacitive Load 3: Resistive I. II. 1₁ Load 1 1₂ Load 1 13 Load 1 Information 125 kVA, p.f =0.28 lagging 10 kW, 40 kVAR, 15 kW Find the total active power, Reactive power, Apparent power, and the power factor of power supply? A pure capacitor (c) is connected in parallel with above loads to improve the power factor to 0.8 lagging. Find the kVAR and the capacitor in µF.

1) Three loads are connected in parallel across a 1400 V, 60 Hz, single phase as shown in below: 1400 V I Load Load 1: Inductive Load 2: Capacitive Load 3: Resistive I. II. 1₁ Load 1 1₂ Load 1 13 Load 1 Information 125 kVA, p.f =0.28 lagging 10 kW, 40 kVAR, 15 kW Find the total active power, Reactive power, Apparent power, and the power factor of power supply? A pure capacitor (c) is connected in parallel with above loads to improve the power factor to 0.8 lagging. Find the kVAR and the capacitor in µF.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

Convert the following instantaneous currents to phasors, using cos(t) as the reference. Give your answers in both rectangular and polar form. (a) i(t)=5002cos(t30) (b) i(t)=4sin(t+30) (c) i(t)=5cos(t15)+42sin(t+30)
what is the reactive power absorbed by the load ZL in VAR? Assume source is in rms
An rms voltage of 22.2 V with a frequencyof 1.00 kHz is applied to a 0.290-mH inductor. (a) What is the rmscurrent in this circuit? (b) By what factor does the current changeif the frequency of the voltage is doubled? (c) Calculate the current for a frequency of 2.00 kHz
6. What is the effect of load inductance on the ripple current? 7. i effect of chonnine Bock and boost 8. Wh 9 What chopping 10. At what duty evcle does the load current rinnle current he
15. You are working on a power factor correction installation, and you notice with a clip-on ammeter as you add in capacitance the current drops, you add more capacitance and the current drops, you add more capacitance the current rises. How do you know when you are at unity power factor?
A 220 Ω resistor is in series with an 80 mH inductor. The AC source is 48 at 1 kHz. The power factor is ________. Hint: Draw the circuit and get Vs and Is
When a resistor is connected across the terminals of an ac generator (117 V) that has a fixed frequency, there is a current of 0.332 A in the resistor. When an inductor is connected across the terminals of the same generator, there is a current of 0.365 A in the inductor. When both the resistor and the inductor are connected in series between the terminals of this generator, what is (a) the impedance of the series combination and (b) the phase angle between the current and the voltage of the generator? Note: The ac current and voltage are rms values and power is an average value unless indicated otherwise. (a) Number (b) Number Buda i Vrms R Irms.R Circuit 1 Units Units Vrms. Irms, L Circuit 2 > L Vrms R www Circuit 3
The complex volt amperes in a series circuit are (4300- j2500) and the current is (25 + j43.3)A.Find the applied voltage.
Please read questions carefully i need power factor and Reactive power of load
1. A load of 50 ohms resistance and 0.4 H inductance are connected in series to 100 volts, 60 hz a-c source. What must be the value of the capacitance to be connected in parallel to the circuit to raise the power factor to 0.96 lagging. Draw the circuit diagram.
An inductor and a resistor are connected in series with a function generator. The voltage across the inductor is 10.6V pk. The voltage across the resistor is 3.6V RMS. Calculate the magnitude of the total voltage applied to the circuit.
Which cannot be said since Z is an inductive load in the circuit given below? A) load voltage period is 0.02sec. B) Load voltage peak value is 311V. C) Load voltage frequency is 50Hz D) Load voltage average value is 220V.