1) For purposes of measuring length, the human torso was a convenient tool, and gave us units of---------- -? A) Meter. B) cm. C) foot. D) mm. 2)----- - the output signal consists of a proportion of the external voltage source applied across the two ends of the potentiometer. A) Null-type, B) deflection-type ,C) passive instrument „D) active instrument. 3) The prerequisite for the reduction of systematic errors is a complete analysis of the----? A) Measurement system, B) systematic errors, C) System disturbance, D) Errors.

1) For purposes of measuring length, the human torso was a convenient tool, and gave us units of---------- -? A) Meter. B) cm. C) foot. D) mm. 2)----- - the output signal consists of a proportion of the external voltage source applied across the two ends of the potentiometer. A) Null-type, B) deflection-type ,C) passive instrument „D) active instrument. 3) The prerequisite for the reduction of systematic errors is a complete analysis of the----? A) Measurement system, B) systematic errors, C) System disturbance, D) Errors.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Read each statement carefully and answer by True or False (if False then, correct the statement). 1- Process control combines how physics, chemistry, and biology work in operating equipment and an understanding of dynamic systems. 2- When a second letter is used in instrumentation symbols, e.g., Pressure Indicator Controller (PIC), it defines the measured or initiating variables. 3- P&ID contains the sensor details such as physical principle and measurement range. 4- FRC 82516: Flow Recording Controller, area no 825, process unit 8, loop number 16. 5- P&ID excludes equipment identification.
d) The generated voltage of a turbine at time t seconds is given by: v(t) = Vgsin(0.4nt + Where Vs is generator voltage in Volts. Evaluate the following: iii. The voltage of the generator after 2.5 seconds if Vs = 70 V. The voltage at time t = 0 seconds to 3 significant figures The time when the generator first reaches maximum voltage, the period, the frequency, and the time displacement. iv. v. Your answer to this part of the task should be supported by suitably annotated graphical evidence to help understanding by a non-technical audience. e) If the cable of this generator has a shape of the form: y = 70cosh(x/55)sinh?( m. Provide fully explained solutions to the following: vi. The value of y when x = 10 to 3 significant figures The value of x when y = 40 to 3 significant figures Provide fully explained graphical evidence to justify your answers to part (vii) vii. viii.
A) As the head of the Accelerometer Design Division (ADD), based on the following figures, advise your team on the production an accelerometer to reduce or eliminate distortions in the readouts. Magnitude ratio M(Go) 2.0 1.5 1.0 0.8 0.6 0.4 0.2 0.1 0.05 I 0.1 = 10.0 I 0.20 5.0 0.5 w/wn 2.0 H 1.0 {=0 0.3 0.4 0.5 0.707 1.0 2.0 3.0 +6 +3 0 -3 do d Decibels (dB) -10 -15 Resonance band Transmission band Filter band Phase shift [°] +(6) 0 -20 -40H -60 -80 -100- -120- -140 -160 -180 0.05 0.10 10.0 0.20 0.50 (=0 1.0 10.0 5.0 2.0 1.0 0.7 0.5 0.4 = 0.3 I 2.0
a) Describe static sensitivity and time constant of instrument?b) A thermometer having a time constant of 1 min is initially at 50 oC. It is immersedin a bath maintained at 100 oC at time = 0. Express temperature in oC at time = 1.2min
During ansys simulation, Designers always get deferent result when they change mesh size. True False
5. A sensor is a device that receives and reacts to a signal such as a change in position, temperature, pressure, concentration, speed, flow, or voltage. a) Explain the temperature sensor and lambda sensor b) Describe the tire pressure gauge
3. The results of a simple calibration of pressure transducer and its specification are shown in Figure 1 and Table 1. The sensitivity of the pressure sensor is 0.5 V/kPa (given by manufacturer) and the linear curve fit for the upscale calibration is given as y = 0.51x +0.02 . a) Calculate the hysteresis and linearity errors for this calibration. b) Please discuss either the pressure transducer can now be used for the actual measurement or not. Table 1: Pressure tansducer specification Оperation Input range 0- 5 kPa + 15 V 0 - 2.5 V Excitation Output range Performance Linearity error ± 3 % Hysteresis Less than + 15% Sensitivity error + 5% Thermal sensitivity error + 0.02% / °C Temperature range 0 - 50 °C 2.5 upacale mesurement downscale measurement 0.5 0.5 3.5 pressure, kPa Оприt, voltage ((V) Upscale Input, pressure (kPa) Downscale 0.00 0.00 1 0.53 0.48 2 1.05 0.94 3 1.62 1.45 4 2.12 1.95 5 2.50 2.50 Figure 1: Calibration results (plot and tabulated data)
b) Figure 1 shows the calibration data of a sensor. Determine the static sensitivity at the input of X= 0, X= 5 and X= 10. For which input values is the system more sensitive? Calibration Data 300 250 y = 0.875x1.055 200 150 100 50 20 40 60 80 100 120 Input value, cm Figure 1 c) Suppose you found a dial thermometer in a stockroom. Discuss several methods by which you might estimate random and systematic error in the thermometer? How would you estimate its uncertainty? Output value, V
OL(A) Consider the Rudimentary Pressure Gage shown in the Figure 1. Then answer the following questions: 1. Sketch the specific schematic diagram of functional elements for this measuring instrument. 2 Is the Rudimentary Pressure Gage considered as a Null or Deflection type measuring device, why? 3. Sketch the specified configuration of input-output relationship diagram including only three quantities of Interfering inputs with only three quantities of Modifying inputs. Spring Piston Rod Piston Fluid Linkage Scale Poinfer Figure 1.
QUESTION 2 SOALAN 2 a) The DP Transmitter device is used to measure level as an inferential measurement. When installing the DP Transmitter in an open tank at HP tapping point at 0%, the lower range values (LRV) and upper range values (URV) for the transmitter must be determined in order to properly register 0% at the LRV and 100% at the URV liquid level. By referring to Figure 2, calculate the calibrated range with specific gravity, SG is 1.1 and height, H of the tank is 100mm. Peranti Pemancar DP digunakan untuk mengukur paras sebagai ukuran taabir. Apabila memasang Pemancar DP di tangki yang terbuka di HP titik tirus pada 0%, nilai julat yang lebih rendah (LRV) dan nilai julat atas (URV) untuk pemancar mesti ditentukan untuk daftarkan betul pada 0% LRV dan 100% URV. Dengan merujuk Rajah 2, hitungkan julat yang dikalibrasi dengan graviti spesifik, S.G adalah 1.1 dan ketinggian, H tangki adalah 100mm. Tank open to Atmosphere Махт. Level Liquid DP Transmitter Vented to Atmosphere Min.…
5) Which type of distortion measurement technique used a spherical ruby stylus? O LVDT O Dial gauge O 3-D CMM O laser beam triangulati
Q3)Explain how can we use the Linear Variable Differential Transformer (LVDT) as a. A flow measuring device.b. A pressure measuring devicec. A force measuring device