(1) A well is drilling to the depth of 6000 m. Formation pore pressure can be expressed in equivalent mud weight is 1.50 g/cm at the depth and changes in proportion to well depth. Also, overburden pressure gradient is 0.0245 MPa/m. Calculate: a. Pore pressure gradient at 6000 m, MPa/m. b.Pore pressure, psi, at 6000 m. c. Matrix stress gradient, MPa/m d.Matrix stress at 6000 m. MPa

(1) A well is drilling to the depth of 6000 m. Formation pore pressure can be expressed in equivalent mud weight is 1.50 g/cm at the depth and changes in proportion to well depth. Also, overburden pressure gradient is 0.0245 MPa/m. Calculate: a. Pore pressure gradient at 6000 m, MPa/m. b.Pore pressure, psi, at 6000 m. c. Matrix stress gradient, MPa/m d.Matrix stress at 6000 m. MPa

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter11: Compressibility Of Soil

Section: Chapter Questions

Problem 11.4P

See similar textbooks

Similar questions

Give the correct option In a drained triaxial test on consolidated clay the stress and angle are as follows: Deviator stress is 20 lb/in2 and friction angle is 21°. Calculate the effective confining pressure at failure?a) 21 lb/in2 b) 22.2 lb/in2 c) 25.4 lb/in 2 d) 17.9 lb/in2
In a drained triaxial test on consolidated clay the stress and angle are as follows: Deviator stress is 20 1b/in2 and friction angle is 210 . Calculate the effective confining pressure at failure.? A) 21 1b/in2 B) 22.2 1b/in2 C) 25.4 1b/in2 D) 17.9 1b/in2 make it fast
A consolidated drained triaxial is conducted on a normally consolidated soil with chamber confining pressure of 152kPa. If the deviator stress failure is 250kPa, determine the following: a. Calculate the angle of friction of the soil (degrees) b. Calculate the shear stress at the failure plane (kPa) c. Calculate the normal stress at the failure plane (kPa)
In a drained triaxial test on consolidated clay the stress and angle are as follows: Deviator stress is 20 1b/in2 and friction angle is 210 . Calculate the effective confining pressure at failure.? A) 21 1b/in2 B) 22.2 1b/in2 C) 25.4 1b/in2 D) 17.9 1b/in2
The coefficient of permeability of a sand at a void ratio of 0.62 is 0.03 cm/sec. estimate the coefficient of permeability at a void ratio of 0.48. a. Using Casagrande equation b. Using kozeny - Carman equation.
Q: For the soil profile shown in figure. Find: a) Final consolidation settlement. b) Time required for 60% consolidation. c) Pore water pressure after 18 months. d) Piezometer reading above point (A) immediately after applying the load. Surcharge Aq.= 100 kPa Sand y=15kN/m’ 7kN/ m® Piezometer t AT ol g thefity i
In a drained triaxial test on consolidated clay the stress and angle are as follows : Deviator stress is 20 lb/in2 and friction angle 210 . calculate the effective confining pressure at failure.?
Figure B: Stress diagram Total Stress (6) Pore Water Pressure (u) Effective Stress (o') 26.2 kPa 26.2 kPa -2.0 m \71.2 kPa 25 kPa i) ?? kPa -4.5 m Vii) ?? kPa 70 kPa 90.3 kPa -9.0 m Figure B Stress diagram Now, assume groundwater table is far, referring to the Figure B, calculate the dry unit weight for 2nd layer (depth below existing ground surface from 2 m till 4.5 m). Assume the specific gravity is 2.65 and unit weight of water is 10 kN/m3. Answer in kPa with two decimal place only. (Please write down value only. Don't input unit in the answer) Your answer
Quize (3): A soil sample is subjected to an all-round pressure of 100 kN/m, the pore water pressure was 93 kN/m. With the drainage valve remains closed an increment of principal stress difference (o, -o,) was applied causing the pore water pressure to increase to 133 kN/m. Knowing that A-0.4, determine B and (o, -a,). 1 Add file
1. A sand specimen is isotropically consolidated in a triaxial test apparatus under a cell pressure equal to 420 kPa and then sheared with the drainage valves open (i.e. CD test). At failure, the deviatoric stress is 1046 kPa. Determine the major and minor principal stresses at failure and the effective internal friction angle (assume c' = 0). Plot the Mohr diagram.
2. The depth of water in a well is 3 m. Below the |IAVA bottom of the well lies a layer of sand 5 meters thick overlying of the clay deposit. The specific clay a gravity respectively 2.64 and 2.70. Their water contents are respectively 25 and 20 percent. Compute the total stress, effective stress and the pore water pressures at pointS solids of sand and are 3m A and B of the figure shown. Sand 5 m A• Ans: 88 kN/m², 29.1 kN/m², 58.9 kN/m² $2 m 12 m Clay
i. A sandstone core sample is saturated 100% with water. Calculate the absolute permeability of the core sample if the water is flowing at 6.21 cubic centimetres per second. The length of the core sample is 14 centimetres and its diameters is 6 centimetres. The pressure differential across the core sample is 15 atmospheric pressure and the water viscosity is 1.2 centipoises. Explain a method of how the permeability of low permeability reservoirs can be ii. improved.