Experiment 4a Synthesis

The objective of this experiment is to separate a 50:50 mixture of benzoic acid and benzil by using macroscale extraction. In the experiment, organic solvent diethyl ether is used. After adding 1.0 gram of the 50:50 mixture of benzoic acid and benzil to a 25ml Erlenmeyer flask, diethyl ether was added to the flask to dissolve the mixture. Benzoic acid and benzil dissolve in diethyl ether. Once the mixture dissolved in

This experiment combined all the knowledge of the previous labs performed throughout the semester. An unknown mixture containing an organic acid or base and an organic neutral compound in nearly equal amounts needs to be separated to its separate components. An understanding of solubility, extraction, crystallization and vacuum filtration is necessary in order to

A few sources of potential error are as follows: loss of product on glassware throughout the experiment, inadequate measuring of chemicals, "impure" chemicals being worked with, and loss of final product during crystallization processes.

In the first acid extraction of benzocaine, the compound was dissolved in the organic solvent of dichloromethane. When the mixture was shaken with HCl, benzocaine’s amine group gained a proton and became more soluble in water than dichloromethane. This allowed the newly formed hydrochloric salt to migrate to the aqueous layer. However, the addition of NaOH to the acidic aqueous layer regenerated benzocaine by deprotonation, making it insoluble in the aqueous layer. The precipitation of an ionic salt was therefore recovered by vacuum filtration and had a tested melting point range of 85.1C-87.4C compared to 88C-90C, the literature melting point of benzocaine. The similarity in melting point ranges, but low percent yield of 30.37% proves that the extract was somewhat successful. Lower yields may be the result of spillage performed in the lab. In the second basic extraction, the organic layer now included benzoic acid and benzamide. When treated with NaOH to deprotonate benzoic acid, the newly formed sodium benzoate transitioned to the aqueous layer as a sodium salt. Benzoic acid is regenerated once again after the addition of HCl and became insoluble in the aqueous layer after protonation. Its precipitation was then filtered out for a 65.87% recovery. Compared to its literature melting point of 122.41C, the resulting 120.9C-123.5C melting range of the sample also supports the accuracy of the separation due to its similarities and high percent yield. In conclusion, the usage of base and acid liquid extraction was mostly successful in this experiment because it was able to efficiently and properly isolate the impure mixture into two separate components of benzocaine and benzoic acid. By performing the techniques of extraction and vacuum filtration, the similarities between literature and tested

3.0g of salicylic acid was weighed then 3.0mL of acetic anhydride and 6 drops of 85% H3PO4 were added to it. The mixture was warmed over a water bath for 5 minutes while stirring. After warming, 20 drops of distilled water was slowly added. 15mL of water was added then the solution was heated until it became clear. It was allowed to cool and was placed in an ice bath until the solution becomes cloudy. Using pre-weighed filter paper, the mixture was filtered and was allowed to dry in the filter paper.

There are millions of different organic compounds. Most of them are found in mixtures and in order to achieve a pure form they need to be separated, isolated, and purified. However, there are endless numbers of possible mixtures, which make it impossible to have a pre-designed procedure for every mixture. So chemists often have to make their own procedures. The purpose of this experiment was to prepare the student to the real world by them designing their own procedure which will help them understand the techniques of separation and purification better. The goal was to extract two of the components of the

Sodium sulfate has a molar mass of 142.04 g/mol. It has a melting point of 884°C and can be an irritant.

Discard the solution in the appropriate container as directed to you by your lab instructor.

Three grams of a mixture containing Benzoic Acid and Naphthalene was obtained and placed in 100 ml beaker and added 30 ml of ethyl acetate for dissolving the mixture. A small amount (1-2 drops) of this mixture was separated into a test tube. This test tube was covered and labelled as “M” (mixture). This was set to the side and used the following week for the second part of lab. The content in the beaker was then transferred into separatory funnel. 10 ml of 1 M NaOH added to the content and placed the stopper in the funnel. In the hood separatory funnel was gently shaken for approximately one minute and vent the air out for five seconds. We repeated the same process in the same manner one more time by adding 10ml of 1M NaOH.

The crude product was washed by taking the reaction product in the separatory funnel and adding 23 mL of deionized H2O. The mixture was shaken and allowed to settle until layers were observable. The top layer was the desired product and approximately 25 mL of aqueous layer was extracted from the separatory funnel. Next, 25 mL of 5% NaHCO3 was added to the separatory funnel in order to neutralize the acid. This mixture was swirled, plugged with the stopper and inverted. Built-up gas was released by turning the stopcock to its opened and closed positions, releasing CO2 by-product. This was done four times in one minute intervals. The solution was allowed to settle until layers were observable. The bottom layer that contained salt, base and water was extracted from the separatory funnel. The crude product was washed again as mentioned previously.

Objective: The objective of this experiment is to use acid-base extraction techniques to separate a mixture of organic compounds based on acidity and/or basicity. After the three compounds are separated we will recover them into their salt forms and then purify them by recrystallization and identify them by their melting points.

Wash (swirl and shake) the organic layer with one 10-mL portion of water and again drain the lower aqueous layer. Transfer the organic layer to a small, dry Erlenmeyer flask by pouring it from the top of the separatory funnel. Dry the crude t-pentyl chloride over 1.01 g of anhydrous calcium chloride until it is clear (see Technique 12, Section 12.9). Swirl the alkyl halide with the drying agent to aid the drying.

1) Pour 25 mL of the 1 M hydrochloric acid into the beaker and rinse the solid by swirling the acid around in the bottom of the beaker.

One milliliter of 6.00-M phosphoric acid was placed into a 125-mL Erlenmeyer flask using a volumetric pipette. Using a slightly larger pipette, six milliliters of 3.00-M sodium hydroxide was transferred into a 50-mL beaker. Then a disposable pipette was used to slowly mix the sodium hydroxide into the phosphoric acid while the solution was swirled around. Then both the beaker and flask were rinsed with 2-mL of deionized water and set aside. A clean and dry evaporating dish was weighed with watch glass on a scale. Then the solution was poured into the dish and the watch glass was placed on top. The solution was then heated with a Bunsen burner to allow for the water to boil off to reveal a dry white solid. After the dish cooled to room temperature it was once again weighed and the new mass was recorded.

If necessary the centrifuge can also be used to further separate the two layers. A final means of drying the ester product is the addition of granular sodium sulfate.