Chapter 10 Lecture Quiz_ ID-17-32108

what is the working for this question

Estimate the length of conduit to perform the next bends. EMT will be bend using a hand bender. Provide your answer in inches (just the number) using up to 2 decimals. The picture shows two panels connected by a back-to-back 23.5" stubs EMT 3/4" 6.25 ft P

**Note: There is no circuit given for this problem.

17- The electromechanical breakdown depend on the type of the dielectric between two electrodes a- Right. b- Wrong 18- Basic Insulation Level (BIL) is related to the design consideration of the electric device, while Basic protection (BPL) level is related to protection level of the that device. a Right. Wrong. b- 19- As the voltage regulation increased, receiving end voltage will be reduced. Right. b- Wrong 20- We can be using Solar power generation field as a power factor and voltage profile enhancement in Distribution system. (aRight. b- Wrong. 21- From the general electrostatic theories, the field strength at breakdown is given by: a Eb = V/ do =0.6 [Y/ (€ o Er) ] 0.5. b- Eb V/ do = 0.6 [Y / (€ 0/Er )] 0.5. C- Eb V/ do = 0.6 [ Y/(Eo Er) 20.05. d- Eb V/ do = 0.6 [ Y/ (Eo Er) 10.5. 22- Consider plane electrodes with a solid insulator between them. Find the electric field strength at breakdown, if Young's modulus = 10000 (V.F/m2). and the relative permittivity is (36000 TT). If the…

This question apportion control system I need this question in half an hour

We are running 3 wires and a ground in a RMC to a control panel with a 60 amp circuit breaker disconnect in the control panel. The conduit is run along the ceiling where the ambient air temperature is 100 degrees. The control panel feeds our secondary cooling pump. What size are the ungrounded conductors? All conductors have typeTHHN insulation. A   #6 AWG B   600 Kcmil C   #8 AWG D   #2 AWG What size RMC do we need? A   3" B   3/4" C   1" D   1 1/2"

The system having ±0.5% of F.S.D if the full scale deflection is 50 units, then accuracy is _____ a. ±0.25 b. ±1 c. ±0 d. ±0.5

Please answer questions using the figure

Explain the diagrams

I have a wooden toy train that runs on wooden tracks. I would like to place two ESP-WROOM-32 Boards on top of the train. Broadcast communication (which involves radio frequency, not Wi-Fi) would help communicate about the train's lateness to five other wooden trains on the same track. Local communication would help communicate to the train station about the train's lateness. I would also need radio frequency Tx-Rx Modules for discharging and undergoing the signal, and repeaters just in case the signal loses power due to long-distance traveling. My wooden train should be automated. It should run at 4 inches per second, keep a minimum distance of 30 seconds away from the other wooden trains, and make a 17-second-long stop every 500 seconds. What's the procedure to connect the components? What's the Arduino code (C++) for this project?

Part 2: Analysis and selection of the Wind Turbine. The team decides at install a 30 MW wind farm. The turbine that has been selected by the local contractor is an Enercon wind turbine. The specifications of all the available Enercon wind turbine is shown in the attached datasheet. 1. Decide on the required number of wind turbines needed. 2. In your own words, explain what the Betz limit for wind turbines means.

Good morning. Can you answer the question of the second stage equipment and measurements material, engineering, and within 5 minutes, with many thanks and appreciation

Very detailed explanation with full detailed drawing Thank you sir

choose the correct answer In solar power plant, the cost of concentrating collector is more than flat platecollector.    TRUE or FALSE

Could you explain this coffe/tea machine circuit

Please help me solve question 5 below. Please provide a clear and readable solution. Thanks in advance!!! The course subject is Electrical Machines 2. NOTE: The answers are given below. Please provide the solution. If the answer given below is wrong, please give the correct answer. The unit of total load is 200 ohms. Thanks a lot!!!

what is the introduction for MEASUREMENT USING DC BRIDGES

Explain the diagram

Set up using matrices if possible. Detailed answer, please. The answer is 0.5 W.

No plagarism please! Correct and detailed answer will be Upvoted else downvoted

Please answer with correct units and complete solution

Please Solve the Electronics Question in 30 minutes with full complete detail and calculation with a complete answer